• Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.

    We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.

    Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103

Kibler Breach Plug

Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I didn't dry ball my Kibler .32 but I was trying to see how little powder I could shoot with and I swabbed the bore with a wet patch, forgot to run a dry patch down and loaded @10 gr 3f - must have been too wet as I could not get it to ignite. Didn't have a .32 ball puller so I put a screw down without a proper sized collar to keep it centered and proceeded to tear off one side of the ball. Took it home and pulled the breech plug. I have a wrench set from Rice that includes a set of aluminum vise blocks and a tapered wrench - the plug came right out, I pushed the remaining chucnk of lead out the back along with a goopy mess of wet powder, put it back in and it's been fine since! As @olskool stated above, just be certain to align the witness marks. (I also bought proper .32 ball puller with the collar)

I can send you the wrench set to use if you will ship it back when you are finished.
I tried about five times getting some 4F in there. I have thought about maybe some ether/starting fluid...

I have a big vice, but as was said, it is tapered and I haven't found a wrench that really fits well enough to put force on it.

That's very kind of you. I may take you up on it after messing with it a little more.
 
I tried about five times getting some 4F in there. I have thought about maybe some ether/starting fluid...

I have a big vice, but as was said, it is tapered and I haven't found a wrench that really fits well enough to put force on it.

That's very kind of you. I may take you up on it after messing with it a little more.

This is all you need.
 

Attachments

  • IMG_4523.jpeg
    4.5 MB
  • IMG_4524.jpeg
    IMG_4524.jpeg
    1.6 MB
i recently got a cva pa.rifle with a blockage 4 inches down the bore. got out my track s/s rod and one of their collared very pointy pullers and got it screwed into the ball in the barrel. after some lube and a lot of tugging it started to move, i was very surprised to find 1/2 of one of those cheap non collared pullers already stuck in the ball luckily to one side..
 
The only time I have needed to "get something out of there" was when I have dry balled which I admit is most usually when I am visiting at the loading bench instead of paying attention to what I am doing. I have never got a brush stuck or the other unique things some have done.

We don't have a vise at the range I shoot at but we do have a piece of angle iron mounted in the rafters with a slot in it that you can hook your range rod into if you need to pull a dry ball.

I usually just shoot it out because I am not leaving to drive home to find a vise when I still have shooting to do, I did buy one of those CO2 things about two years ago but have not had a chance to use it yet.
 
Last edited:
I find tapping the rod with a “T” handle first with a hammer or mallet to start the stuck ball moving works good. Then you can pull it
 
WOW! I can't believe so many people are afraid of pulling a breech plug. My first build was a scratch build and I didn't know anything about breechplugs or timing one to a barrel, I screwed up the fit so bad I had to have material tig welded to the tang twice to start over. By the time I got the breech face fit right I had probably had the breechplug in and out 30 times. I didn't mar the barrel or the tang pulling the breechplug as many times as I did, I padded everything with leather, even the jaws of my Crescent wrench.

I can take a breechplug out in less than a couple minutes, pop the pins, take out the tang bolt, wrap leather around the barrel and put in my padded vise and out it comes with a crescent wrench. You are not supposed to fit one where it takes a Crescent wrench and a 3' cheater pipe to get it loose. Rice breechplugs are often a very tight fit but with the right tools it is a piece of cake and no more difficult to remove than any other.

I have never removed a TC plug but have 15/16 TC plug wrench in case I have to.

TC plug wrench.jpg


I was at the Alabama Kentucky Longrifle show a few years ago, Jason Rice was there, I bought his plug removing tools which greatly simplify the process of plug removal. I put a couple strips of leather over the Rice vise jaws before I clamped the barrel in them.

rice tools.JPG
 
Last edited:
The fewer guns a person has built, the more difficult they try to make a fix.
Put some powder behind the ball and shoot it out. The puller is already broke, so no need to try to save it. You're not going to damage the bore.
I've dry balled a few times over the past 50+ years of shooting these guns. I've built guns for 42+ years, fixed my own guns, and guns for many others. I have never had a case where it was necessary to remove a breech plug to remove a ball.
The most common damage I have seen from amateurs taking a gun apart is damage to the wood.
 

Latest posts

Back
Top