Nothing special? You’ve got a shooter there my friend! You can burn powder until your fingers are sore! When do you get to pull the trigger?
I’d love to see how it shoots
What Muzzleloading Stuff Did You Do Today?
- Thread starter PathfinderNC
- Start date
Help Support Muzzleloading Forum:
Nothing special? You’ve got a shooter there my friend! You can burn powder until your fingers are sore! When do you get to pull the trigger?
I’d love to see how it shoots
Hopefully July 2nd. I am not yet a member of the shooting range and have to wait for the monthly black power shoot.Nothing special? You’ve got a shooter there my friend! You can burn powder until your fingers are sore! When do you get to pull the trigger?
I’d love to see how it shoots
Not sure where you live but, in the PNW, there is always the woods. Either way, post some pictures! You have a starting load yet? I bet some Kibler guys here have a dozen suggestions.
UPS just dropped off 16 pounds, 2,560, of .310 lead balls from Ballistic Products. I think I should be set for the SMR for a few range settings.
I live in the Albany/Corvallis, OR area. I plan on starting with a .490 ball, .015 patch, and 50 grains of 2F powder. That is what I shoot in my Lyman GPR so should be a good starting point.Not sure where you live but, in the PNW, there is always the woods. Either way, post some pictures! You have a starting load yet? I bet some Kibler guys here have a dozen suggestions.
Plainsman
36 Cl.
Sweet.
I needed a small piece of brass, so I went to the scrap yard to rummage through their stuff, I got a piece of flat 3/16 x 2 x14 long and a bunch of round bar that was there. Paid a dear $5.50 for it, and noticed the end of the long brass round bars was all dirty and when I knocked the dirt off realized it was a range rod with a ball puller on the end. Win for me!
- Joined
- Oct 6, 2020
- Messages
- 1,657
- Reaction score
- 2,717
What part of Albany/Corvallis? My wife’s family have been in Oregon over 150 years. As a couple we lived in Salem for about 10 years. I worked quite a bit in northern Albany, and some in Corvallis on remodels. I shot a couple of times with friends at a gun club on the east side of I5 just south of Corvallis.
- Joined
- Oct 6, 2020
- Messages
- 1,657
- Reaction score
- 2,717
I have some knives I really need to finish first, but I was trying to get myself excited to continue working on my PA fowler kit! So I decided to sand down and playing with stain colors. Here’s where I’m at. The first two pictures are of the same side. The last picture is of the opposite side with a little more brown base. In the second picture, you can see the dark speckles. The stain bleed/ beaded out after most of the area had dried. Any thought?
Attachments
That is the gun club that I have been shooting at. Very nice range and group of shooters.
64Springer
75 Cal.
Going through my Roto-Metals tested sailboat ballast.
50 pound bar of 98 Lead, 1 Tin, 1 Antimony.
Need to melt a bit of it and see if it's soft enough for .58 Minie balls. Don't want the skirts too hard.
If it's too hard, it'll make damn fine hollow point hunting bullets. SPLAT!
Some folks think a fiddy dolla test on fiddy poun a lead is a lot. But it's nice to have an actual starting point for recipe additions. I have one 50 pound bar that's 95.5 Lead and 4.5 Antimony. Best 50 bucks I ever spent.
50 pound bar of 98 Lead, 1 Tin, 1 Antimony.
Need to melt a bit of it and see if it's soft enough for .58 Minie balls. Don't want the skirts too hard.
If it's too hard, it'll make damn fine hollow point hunting bullets. SPLAT!
Some folks think a fiddy dolla test on fiddy poun a lead is a lot. But it's nice to have an actual starting point for recipe additions. I have one 50 pound bar that's 95.5 Lead and 4.5 Antimony. Best 50 bucks I ever spent.
Attachments
Last edited:
Made my first batch of lubed wads
Found an old pair of white painters shorts that i had tiedyed at some point
Measured around .018 inches sort of
Cut 1.25 inch holes in them
Melted beeswax/tallow lube then added half part olive oil and half part ballistol.
Then coated them and put them in a bag.
My 50 cal is expected to arrive friday.
Cheers
Found an old pair of white painters shorts that i had tiedyed at some point
Measured around .018 inches sort of
Cut 1.25 inch holes in them
Melted beeswax/tallow lube then added half part olive oil and half part ballistol.
Then coated them and put them in a bag.
My 50 cal is expected to arrive friday.
Cheers
Attachments
Spent time with a cousin south of Lexington, her property was originally owned by the Boone family (of which she is descended). She has the original ox yoke used by my several greats grandfather used to cross the Alleghenies in 1815/16.
The Muzzleloading part - well it’s close enough as I’m sure grandad carried one, the entire way…
The Muzzleloading part - well it’s close enough as I’m sure grandad carried one, the entire way…
it is hard to tell really, I like side one though. Put some oil on it and see what looks better to you
- Joined
- Oct 6, 2020
- Messages
- 1,657
- Reaction score
- 2,717
Very cool!!
- Joined
- Oct 6, 2020
- Messages
- 1,657
- Reaction score
- 2,717
I have a coat of oil on it already! I will add another first thing in the morning!
What I will be doing...
... is sticking around the house and keeping my eyes open for the powder order from Grafs to arrive.
They used the absolute worse shipper in my area and if I don't see them first they are likely to leave without making themselves known.
I'm really interested to see how Swiss powder works and if I notice a difference.
... is sticking around the house and keeping my eyes open for the powder order from Grafs to arrive.
They used the absolute worse shipper in my area and if I don't see them first they are likely to leave without making themselves known.
I'm really interested to see how Swiss powder works and if I notice a difference.
Nice piece of wood, should show very nice with a couple more coats.
spent the last couple of days repairing the mountain rifle. at the June shoot i had a bolster failure the second in almost 40 years where the threads had eroded away. I believe that this is caused by not paying attention to making sure that the threads are long enough on the nipple. both of the failures were because I had installed a flash cup under the nipple. i checked my stock of nipples and indeed there was different lengths of threads on them all of the cones were the same length. I removed the bolster and made a new proper one (not the ones that are sold as replacements ) torqued it in place bore it from the muzzle and then drilled and taped it for the new nipple. posted a June target and tested it it's as good as i can hold and see any more. i believe that a contributing factor to the problem is the nipple and cup don't sit flat on the radius of the bolster and the cup aggravates the problem the cure is to use a counter bore to create a flat for the nipple to seat on or radius the bottom of the cup to match the radius of the bolster and use longer threads on the nipple.
