Isn’t a 10.3mmX60R and 20ga 2 3/4 make that a breechloading cartridge gun? It’s pretty, but wrong forum.
Last edited:
What Muzzleloading Stuff Did You Do Today?
- Thread starter PathfinderNC
- Start date
Help Support Muzzleloading Forum:
Banjoman
Hillbilly
I've got a TC white mountain carbine barrel being delivered today 
Took my .50 caliber woodsrunner to the range yesterday. Since I got it, I have been shooting it with 50 grains of 2F GOEX, .015 patch and .490 ball. I decided to try increasing the powder charge to 55 grains. I think that it might have tightened the group a little. The target on the right s with 50 grains the other two are with 55 grains. The two on the right were off a bench rest while the laft target is offhand. Anyway, it was a great day full sun, no wind, 67 degrees.
It’s a good thing drool doesn’t go through electronic media. That double would covered in slobber.
I was looking over a Pedersoli .45 pistol I purchased a while back, its just been sitting, I havent shot it yet. I noticed a little reddish stuff around the nipple base, also the hole looked plugged. Uh oh.
Put my T handle wrench on it, no way. Put some oil around it, tapped it a few times to wake it up, NADA. Took out the clean out screw, put oil in there, then took an open end wrench to the nipple and just got it to budge, more oil, back and forth and after a few minutes I got it out. Lots of rust inside the chamber etc.
Spent about a half hour cleaning it all out, bore is fine, have a new nipple in place while the other soaks in oil, but the powder chamber had rust so was able to get most of that out, then dribbled oil down bore and let sit. Will swab it out later.
Put my T handle wrench on it, no way. Put some oil around it, tapped it a few times to wake it up, NADA. Took out the clean out screw, put oil in there, then took an open end wrench to the nipple and just got it to budge, more oil, back and forth and after a few minutes I got it out. Lots of rust inside the chamber etc.
Spent about a half hour cleaning it all out, bore is fine, have a new nipple in place while the other soaks in oil, but the powder chamber had rust so was able to get most of that out, then dribbled oil down bore and let sit. Will swab it out later.
Got both muskets out to check pull trigger. My artillery model, having just shot it, and knew it was light; let go with one pound. Adjusted land on tumbler until it held at 3 1/4 lb. Full length musket checked at 3 1/2 lbs. Ready for upcoming shoots!
Made a batch of caps using the new .005" brass sheet I got, then tested them in a 1860 Army revolver. I'm very happy to report that they work 100%, so much better than the beverage can caps I was making. Also charred two rolls of TP for tomorrow's batch of BP. Oh, and ordered a Kibler SMR kit. Woo Hoo!
TDM
Cannon
- Joined
- May 28, 2022
- Messages
- 9,660
- Reaction score
- 24,235
- Location
- Louisiana & My camp in Mississippi
Finished a drum repair on the Traditions .50 I gave my granddaughter. I bought a new CVA drum that was supposed to fit but it didn’t. Used an oversized drill/tap/nipple from TOW. Also the old drum was too long and extended into the chamber, ground it down and chamfered the end. She needed the stock shortened too, so I cut it down to an 11” LOP and reshaped the butt pad. I’ll run some heavy loads through it before I give it back to her.
Attachments
TDM
Cannon
- Joined
- May 28, 2022
- Messages
- 9,660
- Reaction score
- 24,235
- Location
- Louisiana & My camp in Mississippi
You read my mind. I was thinking I should have rung it out with heavy loads BEFORE I cut the stock!
- Joined
- Nov 14, 2010
- Messages
- 1,250
- Reaction score
- 1,698
I glued some leather and flints together.
I was told that it will make it easier if I have to change a flint while I’m at the range shooting.
I was told that it will make it easier if I have to change a flint while I’m at the range shooting.
Bought a few rifles on auction site. Disassembled cleaned and lubed 2 of them today and plan to test fire tomorrow. One is a .50 with 1-1/8” Douglas barrel and other appears to be a.41 caliber. Need a tang sight for the .41 rifle.
TDM
Cannon
- Joined
- May 28, 2022
- Messages
- 9,660
- Reaction score
- 24,235
- Location
- Louisiana & My camp in Mississippi
Three of the six just need cosmetic work, two older ones (circa 1835 and 1845~1875) have pretty rough bores and may need to be rebored or lined if I can’t clean them up myself. One other rifle is .50 smoothbore in really rough shape, and will be a wall hanger. Didn’t really care about it but it was included in one of the lots I bought.
aussie pete
40 Cal
Hi lads and ladies! A wonderful day at the local range here in Townsville today, for our monthly competition. Three targets at 50 metres; 13 shots at each target, counting the best ten shots on each. Only one shooter shot better than me, a difference of 5 points. Very close! The best of all though - lots of banter, camaraderie, and all the noise and smoke associated with our unique sport!
Cheers, Pete
Cheers, Pete
- Joined
- Nov 14, 2010
- Messages
- 1,250
- Reaction score
- 1,698
What did you use to make it with .
Similar threads
