• Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.

    We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.

    Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103

Fusil de Chasse , for fella in N.H.

Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Drilling for tang / trigger plate bolt . Sure hope these holes meet in the middle ....
 

Attachments

  • IMG_20230916_161144.jpg
    IMG_20230916_161144.jpg
    2.8 MB
  • IMG_20230916_161119.jpg
    IMG_20230916_161119.jpg
    2.9 MB
Fusils are a pain in the arse over N.W. guns ...any who , drilled the hole , spotted and drilled tang , then drilled trigger plate , tappedtrigger plate, counter sunk tang , threaded tang screw , fit screw , cut it to length ... Fit it all and checked for lock function ...all good . That tuna sammich is not sittin well on the tummy ......ugh !!
 

Attachments

  • IMG_20230916_162818.jpg
    IMG_20230916_162818.jpg
    3.1 MB
  • IMG_20230916_163341.jpg
    IMG_20230916_163341.jpg
    3.3 MB
  • IMG_20230916_165453.jpg
    IMG_20230916_165453.jpg
    3.9 MB
  • IMG_20230916_163752.jpg
    IMG_20230916_163752.jpg
    4.1 MB
Think I'll slab off the lock side , forestock... WALT53 , watch ....the line is just the marker along the barrel , real quick , its about 1/4" from barrel . its just to get rid of some of the bulk along barrel , dont cut any closer and stop in front of lock mortice , should be marked on stock and barrel ...... Not a lot on this gun ... Dont do the other side ....
 

Attachments

  • IMG_20230916_174743.jpg
    IMG_20230916_174743.jpg
    2.7 MB
  • IMG_20230916_174756.jpg
    IMG_20230916_174756.jpg
    3.2 MB
  • IMG_20230916_175335.jpg
    IMG_20230916_175335.jpg
    3.4 MB
  • IMG_20230916_175814.jpg
    IMG_20230916_175814.jpg
    3.1 MB
  • IMG_20230916_180216.jpg
    IMG_20230916_180216.jpg
    2.8 MB
  • IMG_20230916_180229.jpg
    IMG_20230916_180229.jpg
    2.9 MB
Last edited:
Think I'll slab off the lock side , forestock... WALT53 , watch ....the line is just the marker along the barrel , real quick , its about 1/4" from barrel . its just to get rid of some of the bulk along barrel , dont cut any closer and stop in front of lock mortice , should be marked on stock and barrel ...... Not a lot on this gun ... Dont do the other side ....
How much do you allow in front and back of lock mortise Rob 1/2”or there about.
 
Fightin me a bit , wanted to get the BP down before the end of day but alas ...not to be ...gettin in a hurry cause its gettin dark , gettin close to quittin time, so gonna stop for the day , dont wanna get in a hurry and mess somethin up . Need ta dump a bucket of water over my head and find my lazy spot and watch " Mountain Men " DVDs while thumbing through this forum :)
 

Attachments

  • IMG_20230918_185212.jpg
    IMG_20230918_185212.jpg
    3.1 MB
  • IMG_20230918_183338.jpg
    IMG_20230918_183338.jpg
    3.5 MB
  • IMG_20230918_185206.jpg
    IMG_20230918_185206.jpg
    3 MB
  • IMG_20230918_185202.jpg
    IMG_20230918_185202.jpg
    2.7 MB
  • IMG_20230918_190337.jpg
    IMG_20230918_190337.jpg
    3.7 MB
  • IMG_20230918_190339.jpg
    IMG_20230918_190339.jpg
    3.6 MB
Last edited:
Hmmm..... Not quite a Wallace Gusler hand made screw but .... Dont look bad at all ! Sure sucks the dont make strait slot wood screw's anymore ....
 

Attachments

  • IMG_20230919_123800.jpg
    IMG_20230919_123800.jpg
    4.5 MB
  • IMG_20230919_124756.jpg
    IMG_20230919_124756.jpg
    3.9 MB
  • IMG_20230919_123938.jpg
    IMG_20230919_123938.jpg
    4 MB
  • IMG_20230919_123931.jpg
    IMG_20230919_123931.jpg
    3.7 MB
  • IMG_20230919_123534.jpg
    IMG_20230919_123534.jpg
    2.6 MB
  • IMG_20230919_121431.jpg
    IMG_20230919_121431.jpg
    3.7 MB
  • IMG_20230919_130504.jpg
    IMG_20230919_130504.jpg
    3.6 MB
  • IMG_20230919_130450.jpg
    IMG_20230919_130450.jpg
    3.6 MB
Back
Top